Bluetooth ELM327 v1.2a VPW, PWM, KWP, ISO, CAN Bus Interface

£49.99

Description:

 ** Genuine Elm Electronics v1.2a Chips - No pirate copies here! **
 
The time has arrived where anyone can now diagnose their car, easily and affordably! Here is an adapter that does all of the hard work of protocol translation into a simple ASCII character based view.
 
Via a bluetooth interface, this adapter is used as an interface to connect virtually all OBD-II compliant vehicles to a PC for on-board diagnostics (OBD). Such vehicles are VW, Audi, Seat, Skoda, Opel, Vauxhall, Alfa, Mercedes, Smart, Renault, BMW, Peugeot, Citroen, Lotus, Ford, Rover, Aston Martin, Ferrari, etc.
 
You can also use it with many other software products that require a ELM327 compliant interface, examples of which are listed below in the Supported Software section.
  • Genuine ELM327 v1.2a chipset based design.
  • Supports 9 protocols in all - SAE J1850 PWM, SAE J1850 VPW, ISO 9141-2 and ISO 14230-4 as well as CAN Bus ISO 15765-4.
  • Precision-moulded diagnostic connector made to fit all VW/Audi vehicles, even those with "tight" trim around diagnostic socket.
  • Bluetooth Serial port design.
  • Bluetooth rates Important -> use only 9600 baud.
  • Internal EEPROM can remember the last protocol.
  • Voltage input monitors your vehicle battery.

New for v1.2a

General Items:
  • RS232 baud rates to 500 Kbps
  • Adaptive Timing automatically adjusts ST timeouts
  • Power up to AT MA is selectable
  • Source (tester) address can be changed
  • Can reset all PPs with a jumper
  • Receive addresses can be independently set
J1850:
  • Complete control over in frame responses (IFRs)
  • Delay before protocol 2 helps with some GM/Holden vehicles
ISO 9141 and ISO 14230:
  • The slow initiation address can now be varied
  • Control over key word checking
  • KWP protocols can now transmit 3 or 4 byte headers
CAN:
  • New J1939 protocol
  • Two user-definable CAN protocols
  • Improved error handling and recovery
Technical Specification:
  • ELM327 Based - Datasheet
  • OBDII Plug: J1962 16-Pin Male (to Car)
  • Serial Port : Bluetooth
  • CAN (ISO 15765-4)
  • SAE J1850 PWM
  • SAE J1850 VPW
  • ISO 9141-2
  • ISO 14230-4
  • Automatically searches for the correct protocol or can be configured manually.
  • Bluetooth interface runs at 9600 baud.
  • Serial Interface uses AT commands to look like a modem.
  • Status LEDs
  • Length: 150mm
  • Weight : About 180g
  • Color : Red
Usage:
  • The interface runs at 9600 baud.
  • The PIN code for the interface is "0000".
  • There are two LEDs present on the interface:
    • The Green LED indicates communication with the car and interface.
    • The Blue LED indicates the status of the BlueTooth communication; when pairing, the blue LED will flash. When the blue LED is steady on, this indicates that it is connected to the master device.
  • Select the virtual COM Port occupied by the BlueTooth driver from within your program.
Supported Software:
 
How To Use:
  • Turn the car's ignition switch ON. No need to start the engine.
  • Start the software program, click "Options", select the correct communications port.
  • Your interface now works! Make sure the software can reliably access all the control modules that it should in your car.

Add to Cart:

  • Model: ELMBLUETOOTH
  • Shipping Weight: 0.3g
  • Manufactured by: ECUFix
  • Regular Price: $49.99
  • 1 Units in Stock


This product was added to our catalog on Monday 15 February, 2016.

Your IP Address is: 54.224.75.202
Copyright © 2017 ECUFix. Powered by Zen Cart